-40%
RF Detector with Offset and Zero - SWR Meter
RF Detector with Offset and Zero - SWR Meter
RF Detector with Offset and Zero - SWR Meter
RF Detector with Offset and Zero - SWR Meter
RF Detector with Offset and Zero - SWR Meter
RF Detector with Offset and Zero - SWR Meter
RF Detector with Offset and Zero - SWR Meter
RF Detector with Offset and Zero - SWR Meter

RF Detector with Offset and Zero - SWR Meter

$ 13.72

Availability: 36 in stock
  • Compatible Brand: Universal
  • Refund will be given as: Money back or replacement (buyer's choice)
  • Condition: New
  • Item must be returned within: 30 Days
  • Brand: IVC
  • Return shipping will be paid by: Buyer
  • Type: Filter
  • All returns accepted: Returns Accepted

    Description

    Released: March 2014
    Want to find out how good your antenna is performing? This is a sensitive and accurate high frequency RF detector. It can be used as part of a system to measure the effiency of an antenna.
    Compared to the simpler RDF-01 RF Detector (store.ivc.no), this has a bias adjustment. With DC bias the detector input impedance is reduced significantly for low power transmitters and most of the input power is detected over the output (load) instead. This makes it work more like a RF receiver which boosts sensitivity and dynamic range/resolution. It improves sensitivity with about 12dB.
    The detector is user calibrated using a 3-position slide switch (Off, Bias, Offset) and two multi-turn potentiometers (Bias, Offset); the DC bias pot will raise the voltage to "pre-activate" the diode and the zero offset pot will reset/null the output. The detector voltage is then measured using a multimeter on the therminal block or header. It is designed to work with a -10 dB coupler and an accurate 50 Ohm terminator.
    It works perfect with 915MHz to 5.8GHz transmitters, with input sensitivity from 10mW (-10dBm) to 500mW (27dBm). Input over 500mW should be lowered using 3db/6dB/10dB attentuator(s) (Search Seeed Studio attenuator) between the transmitter and the coupler to get it within the mentioned range, otherwise the rectifier diode will burn out.
    The schottky diode is a Avago Technologies HSMS-2860-TR1G single RF detector. Input plug is a SMA male plug (non-RP). Recommended directional coupler can be found used (Ebay, Aliexpress) by searching for "coupler 10 db sma ghz", make sure the desired frequency range is covered. A terminal block make it easy to hook up multimeter probes or wire extensions.
    Battery not included.
    Based on IBCrazy's and Mictronics' design (www.mictronics.de).
    How to calculate VSWR, please check this page: store.ivc.no/product/rf-detector
    Specifications
    Product ID: RFD-02
    Revision: Rev3 Feb 2014
    Type: RF Detector with DC bias and Zero offset
    Frequency range: 915MHz to 5.8GHz
    Input power: -10dBm (10mW) to +27dBm (500mW)
    Sensitivity: -32dBm (diode capable of -55 to -57dBm)
    Forward bias current: 3uA (100k shunt resistor, equals +0.3V bias)
    Detector output voltage: +0.1-4.0V (max.)
    Connector type: SMA male (center pin, non-RP) 50 Ohm
    DC supply voltage: +1.0 to 1.8V
    Battery slot: AAA LR03/HR03 1.25-1.50V
    Dimensions: 71.48 L x 10.58 W x 11.0 H mm
    Weight: 13 grams (excl. battery
    RoHS compliant
    Designed and made in Europe