3000W Grain Mill Chinese Medicine Grinding Machine Flour Mill Machine

Description

Instruction Manual
Thanks for your use(using) our product-multi-function flour milling machine!
Please carefully read the instruction manual before use the machine.
1
、
Technical parameter
Model
Voltage
Power
N.W.
G.W.
Size
3
6
00
110V/60Hz 220V~240V/50Hz
3
6
00W
5
5
KG
60
KGS
71.5X3
8
X
41
CM
2
、
Operation and Adjustment
1. Please open the front cover, fitted the abrasive disc, spring, apical axis,
bearing ect.
2. Pls insert the hopper into the feed inlet. Pls don’t put much material into
the hopper.every time when the machine are crushing. Avoid to feed too
fast and motor stuck.
3.Order to prevent static abrasive disc rotation loose, please fix it into the
milling cavity.
4. Please p
ut dry stuff into hopper, don’t put wet stuff.into hopper, otherwise
the abrasive disc will be stuck. Then the powder can’t come out.
5. Abrasive disc work time must be adjusted according to powder finess require.
Adjust it to loosen the adjustment nut, powder finess by adjusting screw to  adjust. Please tighten nut after adjusting.
6. Adjust dynamic abrasive disc: remove dynamic abrasive disc firstly,
then loosen the screw of abrasive disc. And taken down spring,
then fixed dynamic abrasive disc, adjustment abrasive disc until two abrasive
superposition.
3
、
Special Safety Rules
1.Please check screw of abrasive disc and feed hopper if it is ok before using the
machine every time.
2.Please clean and dry inside machine after using every time.
3.Please repair or replace the part when the machine parts damaged or abrasion.
4.Do not put the machine inversion please put it horizontal and cut off power.
5.The machine should be installed horizontal on the work table.
6.Please wait a moment to put the material into the machine after turn on
the power. Don’t put much material in the machine to avoid much material and motor stuck.
7.Please remove the material from machine when complete the process and
cut off the power suddenly.
8.
All material must be dry. And don't left metal or stone and other stuff in hopper.
4
、
Assembly instruction
1.
Motor Cover              2.Motor            3.Motor Mounting Flange
4.Motor Bottom             5.Hopper          6. Rubber Cushion
7.Cushion of abrasive disc                    8.
static abrasive disc
9.Crushing Cavity                               10.Adjustment Screw
11.Adjustment Nut         12.Top Axis            13.Bearing
14.Front Cover                      15.
dynamic abrasive disc
16. Grinding Sleeve                17.Adjustment sheet
18.Spring
5
、
General breakdown and operation method
Breakdown phenomenon
Breakdown reason
Correct method
Motor can not start
up
or startup difficultly
Check whether the overload switch is damaged,
The wire diameter is too small voltage is below level
Capacitor is damage .
replace overload switch
replace suitable wire,
when voltage is stable to re-start
Motor weakness
The temperature is too high
Motor cutting-out
motor bearing damage motor work long time
Check motor
Replace motor bearing
According to standard time work or pause.
Machine body is strong quakely
Other part weight not equilibrium
The coupling is bending deformation
Bearing damaged
dynamic abrasive disc not equilibrium
Check the part and adjustment weight equilibrium
Replace coupling
Replace bearing
Adjustment dynamic abrasive disc equilibrium
Crusher room stick or there are metal stuck in it
There are some metals or stuff in machine,
then machine part are damaged.
Cut off power and check hard goods or change part.
.
Grinding is not fine
two abrasive disc is not same level
abrasive disc is coloboma or breaken
Adjustment two abrasive disc are same level.
Change abrasive.
Low efficiency
Abrasive disc is not sharp
Feeding difficultly
Change abrasive
Adjustment the space between of abrasive
The material size is too big
please crush them suitable size.
Motor can’t work
Feeding  too much
Voltage too low
Abrasive disc get stick
Reduce feeding.
Don’t use the machine when the power is not normal.
Adjustment the space of abrasive disc and clean up abrasive disc.
Replace abrasive disc.
6
、
Packing List
Mill Flour Machine
1 pc
Hopper
1 pc
Abrasive disc
4 pcs
overload switch
1 pc
Brush
1 pc
Instruction Manual
1 pc